![wakeonlan online wakeonlan online](https://cdn.comparitech.com/wp-content/uploads/2019/09/Best-Wake-on-lan-tools.jpg)
If the "Power On" request was sent but was not successful, the Unattended Support Computer will remain unchanged (with the " Offline" status and Power On button), but there will be no other indication that it did not work.Click Connect to start an Unattended Support Session with the computer. If the "Power On" request was sent and successful, the Unattended Support Computer's status will change to " Online" with a Connect button (instead of the Power On button).If the "Successful" dialog appears, then wait a few moments and click Refresh at the bottom of the Unattended Support Computers list.Unsuccessful - If no other Unattended Support Computers within the target computer's network are online, the following message appears: "To power on, you must have another online unattended computer on the same network.".
#Wakeonlan online software#
Click OK.Īfter the above configuration, you can now launch a third-party WOL software on PC B and send a Magic Packet to boot up PC A.Note: Although the request was successfully sent, the computer may still not wake up if it does not meet all of the requirements listed above, or if you encounter another error. Power off and then use ASUSTORs Control Center or AiMaster to wake an ASUSTOR NAS in your. Specify the internal server IP as 192.168.0.100, which is the IP address of PC A. Enable the Wake-on-LAN (WOL) function on your ASUSTOR NAS 2. Specify the external port and internal port as 7, which is used to receive Magic Packets. Specify the WAN port according to the network environment. Click OK.Ĭhoose the menu Transmission > NAT > Virtual Servers and click to load the following page.
#Wakeonlan online mac#
Enter the IP address and MAC address of PC A. If there is not a desired entry, click to load the following page. Check if the desired IP address is reserved for PC A. Click OK.Ĭhoose the menu Network > LAN > Address Reservation to load the following page. Enable Export to DHCP Address Reservation. In the IP-MAC Binding List section, click to load the following page. In the Scanning Result section, click the corresponding to bind MAC and IP address of PC A.Ĭhoose the menu Firewall > Anti ARP Spoofing > IP-MAC Binding to load the following page. Wait a minute until the scanning is completed. In the general section, specify the scanning IP range according to the DHCP address pool. The Service to Route the packet is most likely named IP Helper which may support WakeOnLan, but not all Routers support this. If the desired entry is in the list, click the corresponding to bind MAC and IP address of PC A.Ĭhoose the menu Firewall > Anti ARP Spoofing > ARP Scanning to load the following page. There are three methods to do IP-MAC binding: bind in the ARP list, bind in ARP scanning result, or add IP-MAC Binding list entry manually.Ĭhoose the menu Firewall > Anti ARP Spoofing > ARP List to load the following page. To achieve this requirement, you can configure the router as follows:Īfter you complete the configuration, you can use a WOL software to wake up PC A on PC B.įollow the steps below to configure the router.
![wakeonlan online wakeonlan online](https://crypto-truth.com/wp-content/uploads/2021/01/342-1-768x397.jpg)
Make sure the WAN port of the router is routable from PC B.To support wake-up proxy, make sure you select Use wake-up packets only and Unicast. In the Wake on LAN tab, and configure the options that you require for this site. Select the primary site to configure, and then choose Properties. PC A should be powered off normally and the power supply is normal. In the Configuration Manager console, go to Administration > Site Configuration > Sites.In network card properties configuration of PC A, allow the network card to wake up the PC, forbid the PC to turn off the network card to save power, and enable Wake on Magic Packet. Make sure that the network card of PC A supports WOL.In BIOS setup of PC A, enable Power On By PCIE or Wake Up On LAN. On the status bar at the bottom, it reads Magic Packet Sent To 255.255.255.255. Input the MAC Address, Internet Address (local address in this case), Subnet Mask, Send Options: Local Subnet, Port Number 7 (default port), and then click the Wake Me Up button. Make sure that the motherboard of PC A supports WOL. The screenshot below shows the use of the Depicus Wake On LAN GUI.It is required that PC B can wake up PC A by sending a Magic Packet via the internet.īefore configuring WOL, you should do the following preparation: In the diagram below, PC A is connected to the internet via the router. You can use WOL (Wake on LAN) to boot up your PC from a remote place by sending a Magic Packet via the internet.